NF128-201D1
MOOG
T/T
1 year
Availability: | |
---|---|
Quantity: | |
Description:The NF128-201 Power Supply Card is specifically designed to provide power to the circuit cards of the NF120 Series electronics. This power supply unit mounts directly into a dedicated slot within the NF127-101 Motherboard Frame.
Compatibility:
Forward compatible replacement for the F128-201 model.
Key Specifications:
Mounts into a special slot in the NF127-101 Motherboard Frame.
Supplies power to NF120 Series electronics circuit cards.
Technical Specifications
Output Voltages:
+15 VDC regulated, 1.0A max
-15 VDC regulated, 1.0A max
+24 VDC unregulated, 1.0A max
-24 VDC unregulated, 1.0A max
+5 VDC stabilized, 1.2A max (optional)
Note: Total load on +15 & +24 supplies must not exceed 1.2A.
Total load on -15 & -24 supplies must not exceed 1.2A.
Regulation and Ripple:
Load Regulation: ±80 mV max (±15VDC), ±20 mV max (+5VDC option)
Line Regulation: ±10 mV (±15VDC), ±15 mV (+5VDC option)
Ripple: 3 mV (±15VDC), 0.6 mV (+5VDC option)
Temperature Stability: 190 ppm per °C (±15VDC), 20 ppm per °C (+5VDC option)
Input Voltages:
105-130 Vrms (210-260 Vrms optional), 50 to 60 Hz, 40 VA max.
Fuse Requirements:
LittleFuse 218 Series type T or equivalent
AC line: 2 Amp, slow-blow
+24V: 2 Amp, slow-blow
-24V: 2 Amp, slow-blow
Temperature Range:
10°C to 50°C (50°F to 120°F)
Connector:
DIN 41612 style H
Form Factor:
Eurocard 100 x 160 mm, 21HP, 3U
Weight:
4.7 lb (2.1 kg) without +5 VDC option
4.9 lb (2.2 kg) with +5 VDC option
FGU130B | NB2W90R-11 | NP1AY02-MR |
NB2W56R | CTHMIMOD-00 | NP1AXH8VG-MR |
FTU612A | NP1AXH8V-MR | NP1AXH4DG-MR |
NC1X6406 | FNC160A-C20 | NR1TW-16T65DT |
NP1F-MM1 | NP1X1611-RI | NR1DY-16T05DT |
NP1W1606T | NP1Y16T10P2 | NR1SW-16T65DT |
Description
IEC Standards testing procedures require that the mechanical durability test be carried out without current flowing in the main circuit, with the rated voltage applied to the coil and for at least as many on-off operation cycles as specified for the corresponding intermittent duty class as shown in the table on page 5. The mechanical life of the contactor is inversely proportional to the third or fourth power of the operating voltage. Therefore, if the control circuit voltage is 10% higher than the coil’s rated voltage, the mechanical durability will be reduced by half. An increase in control circuit voltage will harm the operating mechanism, core and shading coil. The results of the mechanical durability test for SC series contactors are given in the table below. The electrical durability test must be carried out for the number of operation cycles specified for the corresponding intermittent duty class shown in the table on page 5, and under the circuit conditions of the corresponding utilization category as defined in the table on page 4. Contact wear is caused by arcing that occurs between contacts when the current is interrupted. The amount of contact wear is directly proportional to approximately the second power of the interrupted current value. Therefore, when a contactor is used for inching or plugging operations, the expected service life of the contacts will be much less than if used for normal operations.
More Products
Fuji | Prosoft | Bently Nevada | Schneider |
NP1W1606T | MVI69L-MBS | 1900/65A | 490NRP25300 |
NP1F-MM1 | MVI46-MBP | 3500/65-01-01 | 140AII33010 |
FTU612A | MVI69-MCM | 3500/42 138700-01 | 140XTS00200 |
FGU130B | MVI56E-GSC | 330180-91-05 | 140CRP81100 |
FNC160A-C20 | MVI69E-MBS | 3500/50 133434-01 | AS-B805-016 |
NR1SW-16T65DT | 2150-AGA | 3500/42 140471-01 | 170INT11003 |
NP1X1611-RI | PS69-DPM | 125680-01 | 140DDM39000 |
NJ-JM | MVI71-ADM | 330180-51-00 | 416NHM30032 |
NC1X6406 | MVI69-MNET | 136188-02 | MC-4/11/03/400 |
NP1AXH4DG-MR | MVI56-HART | 125388-01 125388-01H | 140CPS51100 |
Description:The NF128-201 Power Supply Card is specifically designed to provide power to the circuit cards of the NF120 Series electronics. This power supply unit mounts directly into a dedicated slot within the NF127-101 Motherboard Frame.
Compatibility:
Forward compatible replacement for the F128-201 model.
Key Specifications:
Mounts into a special slot in the NF127-101 Motherboard Frame.
Supplies power to NF120 Series electronics circuit cards.
Technical Specifications
Output Voltages:
+15 VDC regulated, 1.0A max
-15 VDC regulated, 1.0A max
+24 VDC unregulated, 1.0A max
-24 VDC unregulated, 1.0A max
+5 VDC stabilized, 1.2A max (optional)
Note: Total load on +15 & +24 supplies must not exceed 1.2A.
Total load on -15 & -24 supplies must not exceed 1.2A.
Regulation and Ripple:
Load Regulation: ±80 mV max (±15VDC), ±20 mV max (+5VDC option)
Line Regulation: ±10 mV (±15VDC), ±15 mV (+5VDC option)
Ripple: 3 mV (±15VDC), 0.6 mV (+5VDC option)
Temperature Stability: 190 ppm per °C (±15VDC), 20 ppm per °C (+5VDC option)
Input Voltages:
105-130 Vrms (210-260 Vrms optional), 50 to 60 Hz, 40 VA max.
Fuse Requirements:
LittleFuse 218 Series type T or equivalent
AC line: 2 Amp, slow-blow
+24V: 2 Amp, slow-blow
-24V: 2 Amp, slow-blow
Temperature Range:
10°C to 50°C (50°F to 120°F)
Connector:
DIN 41612 style H
Form Factor:
Eurocard 100 x 160 mm, 21HP, 3U
Weight:
4.7 lb (2.1 kg) without +5 VDC option
4.9 lb (2.2 kg) with +5 VDC option
FGU130B | NB2W90R-11 | NP1AY02-MR |
NB2W56R | CTHMIMOD-00 | NP1AXH8VG-MR |
FTU612A | NP1AXH8V-MR | NP1AXH4DG-MR |
NC1X6406 | FNC160A-C20 | NR1TW-16T65DT |
NP1F-MM1 | NP1X1611-RI | NR1DY-16T05DT |
NP1W1606T | NP1Y16T10P2 | NR1SW-16T65DT |
Description
IEC Standards testing procedures require that the mechanical durability test be carried out without current flowing in the main circuit, with the rated voltage applied to the coil and for at least as many on-off operation cycles as specified for the corresponding intermittent duty class as shown in the table on page 5. The mechanical life of the contactor is inversely proportional to the third or fourth power of the operating voltage. Therefore, if the control circuit voltage is 10% higher than the coil’s rated voltage, the mechanical durability will be reduced by half. An increase in control circuit voltage will harm the operating mechanism, core and shading coil. The results of the mechanical durability test for SC series contactors are given in the table below. The electrical durability test must be carried out for the number of operation cycles specified for the corresponding intermittent duty class shown in the table on page 5, and under the circuit conditions of the corresponding utilization category as defined in the table on page 4. Contact wear is caused by arcing that occurs between contacts when the current is interrupted. The amount of contact wear is directly proportional to approximately the second power of the interrupted current value. Therefore, when a contactor is used for inching or plugging operations, the expected service life of the contacts will be much less than if used for normal operations.
More Products
Fuji | Prosoft | Bently Nevada | Schneider |
NP1W1606T | MVI69L-MBS | 1900/65A | 490NRP25300 |
NP1F-MM1 | MVI46-MBP | 3500/65-01-01 | 140AII33010 |
FTU612A | MVI69-MCM | 3500/42 138700-01 | 140XTS00200 |
FGU130B | MVI56E-GSC | 330180-91-05 | 140CRP81100 |
FNC160A-C20 | MVI69E-MBS | 3500/50 133434-01 | AS-B805-016 |
NR1SW-16T65DT | 2150-AGA | 3500/42 140471-01 | 170INT11003 |
NP1X1611-RI | PS69-DPM | 125680-01 | 140DDM39000 |
NJ-JM | MVI71-ADM | 330180-51-00 | 416NHM30032 |
NC1X6406 | MVI69-MNET | 136188-02 | MC-4/11/03/400 |
NP1AXH4DG-MR | MVI56-HART | 125388-01 125388-01H | 140CPS51100 |